Skip to main content

Orbital Inspiration!

Looking through my Blog reading list the other day I visited wirework jewellery maker Linda Jones' blog The Wireworkers Guild where I found a tutorial taken from one of Linda's books for her Orbital Rings.



I liked the idea so thought I'd have a go at my own variation of the design.

I used 22g (0.6mm) copper wire as it's easier to wrap and using a thick felt tip marker pen wrapped the wire five times around the pen to create the hoops.
Instead of wrapping the wire all the way round the hoops I wrapped it three times at the top, made a hanging loop then wrapped three times at the other side before trimming the wire and tucking in the end at the back.
I used the other end of the wire to make a few wraps at the bottom of the hoops for balance then trimmed the end and tucked it in at the back.
As the hoops were a good size I had enough room in the centre to add a green opal bead which attaches in the gap left by the hanging loop and dangles in the centre of the hoops. I decided not to hammer them as I didn't want the flattened look then oxidised them (of course!) and attached copper earwires.
I'm really pleased with the end result and the fact they are pretty easy to make. I'm planning on making a Sterling Silver pair possibly in 20g (0.8mm) next!
I've just listed this pair in my Artfire shop and they will soon be listed on Folksy too.




Labels:

Comments

Post a Comment

Your comments and questions are very welcome!
If you would prefer to contact me directly please use the contact form on my "get in touch" page.
Any comments containing links will be deleted so please don't waste your time.....

Popular posts from this blog

Combining Soldering And Enamel

The need to make cute, brightly coloured enamel studs propelled me into the world of combining soldering with enamel a couple of years ago. I knew from reading up on it that it was possible to enamel and solder on the same piece but wasn't too confident I was able to do it back then. It was a slightly embarrassing occurance that made me just get on with - I'd made some enamel studs with glued on stud posts. I'd used 2 part epoxy resin which was a job in itself as it set hard after 5 minutes so I had to keep mixing more up. The finished studs looked ok but that little voice in my head kept asking "are you sure you want to use glue?" I wasn't but didn't think I had any other way to do it so I used glue. I sold my first pair and merrily sent them on their way to Canada. A couple of week later the buyer got in touch to say the stud post had come off one of the earrings and the other was hanging off. I was mortified, apologized profusely and refunded her m...
32 comments
Read more

Amazing Enamel Effects

Buying a kiln recently has given me the chance to experiment with enamelling on larger pieces of copper and to produce some really cool effects. These effects happen when you combine different types of enamel. I usually use smaller flat pieces of copper for making enamelled earrings and have had some of these effects happen when firing with a torch but they are much more obvious when you use larger pieces. I made a few practice pieces which you can see in the photos below. This was flux {a transparent enamel not to be confused with soldering flux!} applied straight onto copper and fired until the copper was a bright golden colour. Then I added a layer of liquid enamel in green and red over the flux and fired again.  The lines and spots form when the enamel becomes hot enough to start moving and in this case the transparent pushes through the liquid enamel layer forming these cool lines and spots. The effect is better in the green liquid enamel than the red.  N...
31 comments
Read more

Embossing Metal With My Sizzix Bigshot

I must admit up until a few weeks ago I was vaguely familiar with the name Sizzix but as to what you actually did with a "Sizzix" I was completely in the dark! That was until I stumbled across a video from Vintaj showing how you could use their embossing folders with a Bigshot to create designs on metal ("metal" - my favourite word after chocolate!) I was really impressed and itching to have a go, I just needed a Bigshot........ I waited a few weeks then when the urge to possess one overcame me I went out debit card at the ready..............and the shop had sold out! So I trundled off to The Range on the off chance and came home clutching my own surprisingly heavy pink and black wonder machine. It sat on the dining room table for a couple of days while I waited for the embossing folders I'd ordered online to arrive then the time came to start playing! I started with some pre-cut 24g copper hearts and the Wildflower Vines and the Butterfly Swirls Deco ...
26 comments
Read more