Skip to main content

I Have Been Busy, Really. Patterned Bronze Sheet.



It's been a bit quiet on the blog front for the past few weeks. I put my Etsy shop and website on holiday just before Christmas so I could have a break, relax and also get cracking with making new jewellery.

I did quite a lot of relaxing {and scoffing chocolates, yum!} over Christmas and the New Year and enjoyed catching up with the end of the second season of The Affair, started watching the second season of Fargo {which to me seems so much better than the first} and other stuff I'd stockpiled with Sky+ .
I did give my shed a proper clean too - even wiping down shelves which were covered with black dust {nice} and I even washed the windows :D

I also got round to making some new jewellery. I felt the need to make some bronze earrings and decided to add some patterns to the sheet bronze with my rolling mill.


I used a mix of textured card, leaf skeletons and brass texture sheet that I'd bought and some brass sheet that I'd etched with a stamped designs.

I started off by cutting the bronze sheet to size then annealed it.


This is me attempting to anneal some bronze sheet and take a photo at the same time.
DO NOT ADJUST YOUR EYES - THE PHOTO IS BLURRY!

I normally buy my textured card from Rolling Mill Resources on Etsy and generally get good results. This blog post from January 2014 shows the results on sterling silver and copper sheet using textured card bought from Rolling Mill Resources.

This time I used some textured card from another shop and have been pretty disappointed with the results to be honest. Below is a piece of bronze textured with one of their cards. The pattern is there but it's pretty faint.



The patterns on these two pieces of bronze turned out pretty faintly too.


Below: this strip was textured using a piece of textured card from Rolling Mill Resources...


Admittedly having a long thin shape makes it easier to impress the pattern onto the metal and I did maybe roll it a little bit too tight which is why the metal has curved but the results are much deeper and clearer.

Compare the card textures to using metal to impress the design...

rolling mill textures using etched brass and machine patterned brass

The bronze on the left was rolled with a piece of etched brass and the other piece with a brass texture plate I bought ages ago. Lovely clear patterns!

rolling mill textures on bronze sheet © Cinnamon Jewellery 2016

I flipped over the largest piece {shown above} that had the faint card texture and used a piece of brass I'd etched with a stamped design. Much better!

I also used a leaf skeleton. You can't go wrong with them, they work so well on all the metals I've tried them with. The fibrous nature of the veins is obviously pretty sturdy.

leaf vein texture on bronze © cinnamon jewellery 2016

The photo collage at the top of this post shows what I did with some of the patterned bronze but more about that in my next post!

Tracy © Cinnamon Jewellery



Copyright © 2016 Cinnamon Jewellery. All rights reserved.

Comments

  1. It must be so fun texturizing the metal like this. I love the results! We would probably like The Affair and Fargo. They are on my long list to watch. We just started binge watching on the American version of Shameless which is hysterical.

    ReplyDelete
    Replies
    1. I never really watched Shameless in the UK but I think I should have :D
      Thanks for your comment Val!

      Delete
  2. You really did enjoy your holiday! The earrings on your collage are all pretty. No wonder how much dedication and effort you put on each of them but one thing for sure, you really enjoyed what you're doing, aren't you? Thanks for sharing!

    ReplyDelete
  3. I love the textures from the etched brass sheets! I need to get me a rolling mill...

    ReplyDelete
  4. It sounds like you enjoyed your break. The holidays are always an extremely busy time of the year. It’s good that you took a break; work can be draining mentally and physically. I love the bronze earrings! I love how you textured the metal. My favorite ones are the leaf earrings. Good luck with your business!

    ReplyDelete
  5. I'm studying your blog with great interest. What happens if you use, not a skeleton, but a dry leaf? A green one would probably smash, but a dry one have a lot of structure, even if it isnt a skeleton. Skeletons are hard to find....

    ReplyDelete
    Replies
    1. Hi, thanks for your comment. You could use a dry leaf. I have some but haven't got round to trying them in the rolling mill yet but I have seen other people using them. You can get skeleton leaves from craft shops and ebay also sell them :D

      Delete

Post a Comment

Your comments and questions are very welcome!
If you would prefer to contact me directly please use the contact form on my "get in touch" page.

Popular posts from this blog

Combining Soldering And Enamel

The need to make cute, brightly coloured enamel studs propelled me into the world of combining soldering with enamel a couple of years ago. I knew from reading up on it that it was possible to enamel and solder on the same piece but wasn't too confident I was able to do it back then. It was a slightly embarrassing occurance that made me just get on with - I'd made some enamel studs with glued on stud posts. I'd used 2 part epoxy resin which was a job in itself as it set hard after 5 minutes so I had to keep mixing more up. The finished studs looked ok but that little voice in my head kept asking "are you sure you want to use glue?" I wasn't but didn't think I had any other way to do it so I used glue. I sold my first pair and merrily sent them on their way to Canada. A couple of week later the buyer got in touch to say the stud post had come off one of the earrings and the other was hanging off. I was mortified, apologized profusely and refunded her m

Etching Silver Using Nail Art Stamps

So my love/hate relationship with etching sterling silver continues. I've tried a few times now and always end up with different results most of them not that great to be honest. I've tried connecting the silver and a piece of copper to a 9v battery and also heating the ferric nitrate. Sometimes the results are good sometimes not so good. I currently have an etched piece of silver sheet waiting to be reticulated and rid it of the mess that is the etched "pattern".  I now know that using stamps and Stayz On ink just doesn't work with silver - the time needed to etch using ferric nitrate is much longer than etching copper and the ink starts to wear away after about an hour. This results in the pattern being patchy as the resist is eaten away and the silver ends up quite lumpy and course looking. I have yet to try using pnp paper. I don't know why but it all seems a bit of a faff to do. I don't have a laser printer so would need to find somewhere or

Embossing Metal With My Sizzix Bigshot

I must admit up until a few weeks ago I was vaguely familiar with the name Sizzix but as to what you actually did with a "Sizzix" I was completely in the dark! That was until I stumbled across a video from Vintaj showing how you could use their embossing folders with a Bigshot to create designs on metal ("metal" - my favourite word after chocolate!) I was really impressed and itching to have a go, I just needed a Bigshot........ I waited a few weeks then when the urge to possess one overcame me I went out debit card at the ready..............and the shop had sold out! So I trundled off to The Range on the off chance and came home clutching my own surprisingly heavy pink and black wonder machine. It sat on the dining room table for a couple of days while I waited for the embossing folders I'd ordered online to arrive then the time came to start playing! I started with some pre-cut 24g copper hearts and the Wildflower Vines and the Butterfly Swirls Deco