Skip to main content

New Sterling Silver Bangle Designs


In my last post I mentioned that I'd been busy finishing a batch of sterling silver bangles so I could get them sent off to the London Assay Office for hallmarking. Well I did just that and got them back last week. After finishing them {they always come back a bit out of shape and with a couple of scratches when they've been hallmarked} and oxidizing the bangles that needed it, I finally got round to getting them photographed. 

I made a few new {to me} designs including this hammered "bark" texture set using flattened 6mm and 4mm round wire.


I got busy with the masking tape for this bangle...


Creating this texture involved cutting very thin strips of masking tape then sticking them to the flattened silver before rolling it through the rolling mill. The textured areas are where the tape was and the raised smooth sections were the bits without any tape. I like this texture! 
I was going to try to achieve the look by wrapping 20g/0.8mm wire around the flattened silver but that would have left the texture on the inside of the bangle also and I wasn't sure if that would cause problems during hallmarking. So I did it the fiddly, playing around with a scalpel and tape way.


This is probably my favourite design. I love the coil and twist texture and it does look cool when it's oxidized.


I made some more bangles with a leaf vein texture too. One set of three made from flattened 4mm sterling silver wire and a single leaf vein bangle made from flattened 5mm wire.



I made a silver version of my loopy bangle too.



I also made a couple of my silver poppy bangles as they are popular - one with an oxidized finish and one shiny shiny.


 I left more than a few of this batch of bangles with a shiny shiny finish which is strange as I usually lean more to the dark {oxidized} side. Some textures just seemed to work better when they were left to their own shiny sparkle-y loveliness :D

I'm currently adding the bangles to my Etsy shop and will be adding them to my website very soon.




Copyright © 2015 Cinnamon Jewellery. All rights reserved.

Comments

  1. Everything is gorgeous as always! Very creative with the tape creating that cool texture!

    ReplyDelete
    Replies
    1. Thanks Val. I do like the stripe texture and think it's worth the fiddling about to do it :D

      Delete
  2. I have been following your blog for years now, since I was on Folksy and I haven't been there for a long while. Love seeing your designs and how you are getting on. :)

    ReplyDelete

Post a Comment

Your comments and questions are very welcome!
If you would prefer to contact me directly please use the contact form on my "get in touch" page.

Popular posts from this blog

Combining Soldering And Enamel

The need to make cute, brightly coloured enamel studs propelled me into the world of combining soldering with enamel a couple of years ago. I knew from reading up on it that it was possible to enamel and solder on the same piece but wasn't too confident I was able to do it back then. It was a slightly embarrassing occurance that made me just get on with - I'd made some enamel studs with glued on stud posts. I'd used 2 part epoxy resin which was a job in itself as it set hard after 5 minutes so I had to keep mixing more up. The finished studs looked ok but that little voice in my head kept asking "are you sure you want to use glue?" I wasn't but didn't think I had any other way to do it so I used glue. I sold my first pair and merrily sent them on their way to Canada. A couple of week later the buyer got in touch to say the stud post had come off one of the earrings and the other was hanging off. I was mortified, apologized profusely and refunded her m

Etching Silver Using Nail Art Stamps

So my love/hate relationship with etching sterling silver continues. I've tried a few times now and always end up with different results most of them not that great to be honest. I've tried connecting the silver and a piece of copper to a 9v battery and also heating the ferric nitrate. Sometimes the results are good sometimes not so good. I currently have an etched piece of silver sheet waiting to be reticulated and rid it of the mess that is the etched "pattern".  I now know that using stamps and Stayz On ink just doesn't work with silver - the time needed to etch using ferric nitrate is much longer than etching copper and the ink starts to wear away after about an hour. This results in the pattern being patchy as the resist is eaten away and the silver ends up quite lumpy and course looking. I have yet to try using pnp paper. I don't know why but it all seems a bit of a faff to do. I don't have a laser printer so would need to find somewhere or

Embossing Metal With My Sizzix Bigshot

I must admit up until a few weeks ago I was vaguely familiar with the name Sizzix but as to what you actually did with a "Sizzix" I was completely in the dark! That was until I stumbled across a video from Vintaj showing how you could use their embossing folders with a Bigshot to create designs on metal ("metal" - my favourite word after chocolate!) I was really impressed and itching to have a go, I just needed a Bigshot........ I waited a few weeks then when the urge to possess one overcame me I went out debit card at the ready..............and the shop had sold out! So I trundled off to The Range on the off chance and came home clutching my own surprisingly heavy pink and black wonder machine. It sat on the dining room table for a couple of days while I waited for the embossing folders I'd ordered online to arrive then the time came to start playing! I started with some pre-cut 24g copper hearts and the Wildflower Vines and the Butterfly Swirls Deco