Skip to main content

Torch Enamel Earrings - More Poppies!


I do seem to have a bit of a poppy thing going on at the moment. My poppy bangle sets are proving to be quite popular - I had several made to order sets and singles to make last week and I sold the silver poppy studs I made too! 

So to carry on the theme because I like the shape I made a couple of pairs of simple enamel poppy earrings too. They are pretty easy to make once the enamelling is done. The balled sterling wire is threaded through the hole in the centre of the poppy then bent at a right angle before being bent up over itself to form a loop at the back that stops the enamelled poppies from flopping forward when the earrings are worn. The wire is then curved into an ear hook and finished.

I made the poppies in minty green and mauve and another concave disc pair in bitter green...



I was thrilled to see my new order of decals arrive today. The designs look really sweet and a bit clearer than the last lot so I'm hoping to have another go with them tomorrow ♥


Labels:

Comments

  1. littleRamstudioFriday, September 12, 2014

    Can't choose a favourite colour!
    Heather :)

    ReplyDelete
  2. Miss Val's CreationsSaturday, September 13, 2014

    Poppies are one of the cutest flowers out there! I can see why they are such a great seller for you. :)

    ReplyDelete
  3. AnonymousSunday, September 14, 2014

    These are very cute, I really like the fact you have gone for pretty but unusual colours, they will stand out beautifully.

    ReplyDelete
  4. Copper WireTuesday, September 16, 2014

    Amazing..... It is hard to choose which one is look so pretty. They all are looks awesome.

    ReplyDelete
  5. Kalaya SteedeWednesday, September 17, 2014

    Nice Torch firing girl! xo

    ReplyDelete

Post a Comment

Your comments and questions are very welcome!
If you would prefer to contact me directly please use the contact form on my "get in touch" page.

Popular posts from this blog

Combining Soldering And Enamel

The need to make cute, brightly coloured enamel studs propelled me into the world of combining soldering with enamel a couple of years ago. I knew from reading up on it that it was possible to enamel and solder on the same piece but wasn't too confident I was able to do it back then. It was a slightly embarrassing occurance that made me just get on with - I'd made some enamel studs with glued on stud posts. I'd used 2 part epoxy resin which was a job in itself as it set hard after 5 minutes so I had to keep mixing more up. The finished studs looked ok but that little voice in my head kept asking "are you sure you want to use glue?" I wasn't but didn't think I had any other way to do it so I used glue. I sold my first pair and merrily sent them on their way to Canada. A couple of week later the buyer got in touch to say the stud post had come off one of the earrings and the other was hanging off. I was mortified, apologized profusely and refunded her m...
32 comments
Read more

Torch Enamelling - What I've been Up To Recently!

I've admired enamelled jewellery for a while now and not too long ago did a blog post about Etsy seller tekaandzoe  and her wonderful kiln enamelled creations. I didn't think at the time that it was something I would ever be able to do as the cost of kilns plus lack of space would be a problem for me. That wasn't until I saw an advert for a torch enamelling tutorial from US jewellery supplies website Beaducation  by Steven James . It's a great tutorial showing the basics on how to torch enamel on copper. Of course I bought it! I then spent hours scouring the internet for more information on torch enamelling, where to buy the tools I'd need and of course the enamel powders. There are quite a few UK sites selling enamelling supplies and tools but as usual I found the US sites had more choice (why do we always lag behind?) I bought some enamel powders from a couple of UK sites to begin with - Cookson Gold have a good selection but bear in mind th...
37 comments
Read more

Etching Silver Using Nail Art Stamps

So my love/hate relationship with etching sterling silver continues. I've tried a few times now and always end up with different results most of them not that great to be honest. I've tried connecting the silver and a piece of copper to a 9v battery and also heating the ferric nitrate. Sometimes the results are good sometimes not so good. I currently have an etched piece of silver sheet waiting to be reticulated and rid it of the mess that is the etched "pattern".  I now know that using stamps and Stayz On ink just doesn't work with silver - the time needed to etch using ferric nitrate is much longer than etching copper and the ink starts to wear away after about an hour. This results in the pattern being patchy as the resist is eaten away and the silver ends up quite lumpy and course looking. I have yet to try using pnp paper. I don't know why but it all seems a bit of a faff to do. I don't have a laser printer so would need to find somewhere or...
34 comments
Read more