Skip to main content

New Copper Bangles - Flowers, Beads, Twists And Linked Designs!


My recent holiday gave me a chance to come up with a few new copper bangle designs. They are a good seller in my Etsy shop and website so I figure expanding the range makes good sense.
I started by making an intertwined set using 2.6mm round copper wire. It's very simple to link the bangles - it just consists of an extra step once you've soldered, shaped and textured them. Two of the bangles need to be cut open again at the solder join and one of them linked with the remaining soldered bangle and the other bangle linked through the first two before they are soldered closed again and finished. I made the bangles slightly bigger than normal to allow for the space taken up by the bangles being linked. I then had a bit of a brain freeze moment about it all and thought they were still going to be too small but opening them out fully and measuring the inside diameter reassured me they were the right size {does that make sense? I hope so!}



Next I made a set using some lovely etched lampwork glass beads made by Su Bagley of Pixel Pyro Lampwork on Folksy. She made the beads with a larger hole than normal so they would fit on thicker copper wire. I made a set of three bangles with a hammered and line texture with one of the bangles having two of the etched lampwork beads threaded onto it before being soldered closed. 


The beads are in four lovely colours.


Next are two sets of poppy bangles - one with a copper poppy and one with a sterling silver poppy. I enjoyed making these even thought the soldering was a bit tricky to begin with {things moved!} However, now I know to make sure the flower has good contact with the bangle before I start soldering.
The poppy is formed then a balled piece of copper/sterling silver wire is threaded through the centre and the flower wire wrapped onto the bangle. I then added another wrap of wire on the other side. It's all soldered in place and the ends of the wire smoothed for comfortable wearing. 



I am slightly biased but these are my favourite of all the bangles I've made so far

The last new design is a set of three with one bangle with a single twist. Deceptively easy to make by folding the wire into a U shape, flattening the top section of the U with a hammer or rolling mill then annealing and pulling the ends in opposite directions. Then just cut to length and make as normal. 



I think that's enough bangletastic-ness for now!

'Til next time......


Comments

  1. Torn between the copper poppy and the simple twist, both gorgeous.
    Heather :)

    ReplyDelete
  2. I love the surprise element of the twisted bangle, its so chic and the poppy bangle has a lot of rhythm to it. I personally love the combination of silver or brass with copper and I wear such a bangle almost everyday

    ReplyDelete
    Replies
    1. Thanks Divya, I like the look of copper and silver together too.

      Delete
  3. These are fantastic Tracy! I really love the poppy flowers. :)

    ReplyDelete
  4. Incredible jewelry in bronze metal. I like it. Very trendy.

    ReplyDelete

Post a Comment

Your comments and questions are very welcome!
If you would prefer to contact me directly please use the contact form on my "get in touch" page.

Popular posts from this blog

Combining Soldering And Enamel

The need to make cute, brightly coloured enamel studs propelled me into the world of combining soldering with enamel a couple of years ago. I knew from reading up on it that it was possible to enamel and solder on the same piece but wasn't too confident I was able to do it back then. It was a slightly embarrassing occurance that made me just get on with - I'd made some enamel studs with glued on stud posts. I'd used 2 part epoxy resin which was a job in itself as it set hard after 5 minutes so I had to keep mixing more up. The finished studs looked ok but that little voice in my head kept asking "are you sure you want to use glue?" I wasn't but didn't think I had any other way to do it so I used glue. I sold my first pair and merrily sent them on their way to Canada. A couple of week later the buyer got in touch to say the stud post had come off one of the earrings and the other was hanging off. I was mortified, apologized profusely and refunded her m

Etching Silver Using Nail Art Stamps

So my love/hate relationship with etching sterling silver continues. I've tried a few times now and always end up with different results most of them not that great to be honest. I've tried connecting the silver and a piece of copper to a 9v battery and also heating the ferric nitrate. Sometimes the results are good sometimes not so good. I currently have an etched piece of silver sheet waiting to be reticulated and rid it of the mess that is the etched "pattern".  I now know that using stamps and Stayz On ink just doesn't work with silver - the time needed to etch using ferric nitrate is much longer than etching copper and the ink starts to wear away after about an hour. This results in the pattern being patchy as the resist is eaten away and the silver ends up quite lumpy and course looking. I have yet to try using pnp paper. I don't know why but it all seems a bit of a faff to do. I don't have a laser printer so would need to find somewhere or

Embossing Metal With My Sizzix Bigshot

I must admit up until a few weeks ago I was vaguely familiar with the name Sizzix but as to what you actually did with a "Sizzix" I was completely in the dark! That was until I stumbled across a video from Vintaj showing how you could use their embossing folders with a Bigshot to create designs on metal ("metal" - my favourite word after chocolate!) I was really impressed and itching to have a go, I just needed a Bigshot........ I waited a few weeks then when the urge to possess one overcame me I went out debit card at the ready..............and the shop had sold out! So I trundled off to The Range on the off chance and came home clutching my own surprisingly heavy pink and black wonder machine. It sat on the dining room table for a couple of days while I waited for the embossing folders I'd ordered online to arrive then the time came to start playing! I started with some pre-cut 24g copper hearts and the Wildflower Vines and the Butterfly Swirls Deco