Skip to main content

A Real Gem - Joopy Gems


I decided last week that I was going to start making rings to sell. I've made a few for myself but so far have shied away from making them because of the possible size problem. By that I mean sending a ring off only for the buyer to contact me to say it's great but it's a bit too big/too small can you resize it? Making to order in the size the buyer asks for should hopefully make this a fairly rare occurance (I hope!) 

I'm going to start with stacking rings - plain and with gemstone cabochons as they seem very popular. I do have a lot of smooth cabs but after closer inspection I found a lot of them are a bit rough in places or even scratched. The saying "you get what you pay for" definitely rings true with cabochons! I've decided for my own sake and the sake of my jewellery it's worth spending more on stones to get the quality I would expect if I was buying handmade jewellery myself. There's nothing wrong with buying cabs in bulk for low prices but if half of them aren't useable it doesn't make much sense really.

After a bit of research I fell in love with rose cut cabochons so the next step was to find a supplier. Rose cuts are cabs that are flat on the bottom and faceted on the top. As usual finding something a bit different is virtually impossible in the UK at the mo, Kernowcraft sell a limited selection but one of the best sources I've found is Joopy Gems. You can also find them on Etsy.





Joopy Gems is run by Brit Julia Aufenast. Based in Hong Kong Julia specialises in rose cut and faceted cabochons as well as smooth cabochons, faceted gemstones and a large range of pearls. What's nice to know is that Julia sources and selects all of the stones herself, seeing the stones in the rough before they are cut. The quality is high and the prices are reasonable. All the photos here are from the website and as you can see the cabs look lovely! I asked Julia if it was ok to do a blog post about her website and she was very happy for me to do so. She told me she has family in West Sussex and also here in Eastbourne so it really is a very small world!




I spent quite a long time deciding what I was going to buy as there is a lot to choose from. The prices are more than I've paid for cabs previously but the quality and choice make it worth it in my opinion. In the end I went for 6mm rose cut cabs in labradorite, prehnite, almandite garnet, amethyst, carnelian and blue chalcedony. A nice rang of colours but there were so many other stones I loved which will have to wait for next time! I did get 10% off my first order which helped too. I'll probably get clobbered for VAT by customs (about £14 according to their online calculator) but it will still make the total cost for each cab reasonable. The postage from Hong Kong was under £4 too which was a pleasant surprise.




I'm eagerly awaiting my first order and as soon as I've made some rings using the cabs I will write a post. I'm so keen for the cabs to arrive I've already made the ring bands!
And here just for the sake of it some more lovely gemstone and pearl photos.......









Labels:

Comments

  1. littlecherryhillFriday, February 21, 2014

    I was as you are now, a little skeptical of making rings because of sizing issues. Still haven't ventured past anything over 5mm wide in ring shank, but it's something on my list to get done as I love the big wide ring shanks other artists use. You'll find those little stones are great for earrings too! Have fun, can't wait to see the finished pieces :)

    ReplyDelete
  2. K S Jewellery DesignsSunday, February 23, 2014

    I've used this supplier and been very happy with my purchases from her and even been back for more! No customs hit yet either which was great. Looking forward to seeing what you make and wish you good luck with your rings.
    Kristin :)

    ReplyDelete
    Replies
    1. Cinnamon JewellerySunday, February 23, 2014

      Thanks Kristin! They arrived on Friday so really quick delivery from Hong Kong and I didn't have to pay any duty on them either :D
      Just finished soldering the bezels to the rings this afternoon so they will be finished soon.....

      Delete

Post a Comment

Your comments and questions are very welcome!
If you would prefer to contact me directly please use the contact form on my "get in touch" page.
Any comments containing links will be deleted so please don't waste your time.....

Popular posts from this blog

Combining Soldering And Enamel

The need to make cute, brightly coloured enamel studs propelled me into the world of combining soldering with enamel a couple of years ago. I knew from reading up on it that it was possible to enamel and solder on the same piece but wasn't too confident I was able to do it back then. It was a slightly embarrassing occurance that made me just get on with - I'd made some enamel studs with glued on stud posts. I'd used 2 part epoxy resin which was a job in itself as it set hard after 5 minutes so I had to keep mixing more up. The finished studs looked ok but that little voice in my head kept asking "are you sure you want to use glue?" I wasn't but didn't think I had any other way to do it so I used glue. I sold my first pair and merrily sent them on their way to Canada. A couple of week later the buyer got in touch to say the stud post had come off one of the earrings and the other was hanging off. I was mortified, apologized profusely and refunded her m...
32 comments
Read more

Amazing Enamel Effects

Buying a kiln recently has given me the chance to experiment with enamelling on larger pieces of copper and to produce some really cool effects. These effects happen when you combine different types of enamel. I usually use smaller flat pieces of copper for making enamelled earrings and have had some of these effects happen when firing with a torch but they are much more obvious when you use larger pieces. I made a few practice pieces which you can see in the photos below. This was flux {a transparent enamel not to be confused with soldering flux!} applied straight onto copper and fired until the copper was a bright golden colour. Then I added a layer of liquid enamel in green and red over the flux and fired again.  The lines and spots form when the enamel becomes hot enough to start moving and in this case the transparent pushes through the liquid enamel layer forming these cool lines and spots. The effect is better in the green liquid enamel than the red.  N...
31 comments
Read more

Embossing Metal With My Sizzix Bigshot

I must admit up until a few weeks ago I was vaguely familiar with the name Sizzix but as to what you actually did with a "Sizzix" I was completely in the dark! That was until I stumbled across a video from Vintaj showing how you could use their embossing folders with a Bigshot to create designs on metal ("metal" - my favourite word after chocolate!) I was really impressed and itching to have a go, I just needed a Bigshot........ I waited a few weeks then when the urge to possess one overcame me I went out debit card at the ready..............and the shop had sold out! So I trundled off to The Range on the off chance and came home clutching my own surprisingly heavy pink and black wonder machine. It sat on the dining room table for a couple of days while I waited for the embossing folders I'd ordered online to arrive then the time came to start playing! I started with some pre-cut 24g copper hearts and the Wildflower Vines and the Butterfly Swirls Deco ...
26 comments
Read more