Skip to main content

Silver Hollow Form Pendant and Earrings


I recently finished my first sterling silver hollow form pendant. In my last post I said how much I love the look of hollow form pieces - the 3D solidness of them despite being hollow. Anyway I still love them after making my first version in silver!

I didn't take any photos this time but I promise to do so next time when I'm planning to make another one with a bezel set cab on the front. I used 24g/0.5mm sheet that I etched using nail varnish as the resist to create a dot pattern. I used a small brush for the nail varnish and managed to get it all over my fingers (course I did). I discovered you get a neater, rounder dot (which is so important to me because I'm slightly weird!) if you load the brush so it's almost but not quite dripping, hence the messy fingers. I bought some 5mm 24g/0.5mm strip from Cookson Gold for the frame or walls of the hollow form which is a bit extravagant I suppose as I could cut it myself but it just makes it a bit quicker to do.

I found the soldering easier to do than on the copper version. I use steel T pins to hold the frames down firmly onto the sheet and I did sand the sheet this time as well as annealing and flattening it with a rawhide mallet. I also used a different flux than usual - Tenacity 5 instead of Auflux. I like Auflux but being a liquid it tends to run everywhere so you need to apply it several times to make sure everything is covered. The Tenacity flux is a powder you mix with water to a paste consistency so it stays put. Incidently I discovered there is a burlesque dancer called Tenacity Flux - good name!


The solder flowed well all round both frames so I didn't have to do any further soldering to fill gaps. One problem I did encounter was fire stain - that greyish/purple staining caused by oxidation within the silver because of too much heat in one spot for too long. I did struggle with the Tenacity flux to know if the solder had actually flowed - it behaves slightly differently to the Auflux and I didn't notice the solder flow so probably held the heat on the silver for too long causing the fire stain. I did manage to remove it with sanding discs and my Dremel so it wasn't a catastrophe plus using liver of sulphur would help cover it up too if you didn't want to sand it out.
I did my usual and started finishing the pendant before I'd finished soldering on the bail and heart so had to sand the edges twice to remove the fire stain. One day I will learn to leave the finishing till after I've finished soldering! The heart was made from a fine silver ball that I hammered then filed into a heart shape. I think it adds a touch of cuteness to the pendant. The final shape of the pendant kind of forms itself - I start off with a shape for the frames them tweak them once they're soldered until I'm happy. I prefer free-form but I do want to try more of a flower/wavy edge shape soon.



The pendant feels fairly substantial at 6.2g despite being made from a thin gauge of silver which is handy as it means I won't need to get it hallmarked. I made some simple silver hollow form disc earrings too....... slightly easier than the pendant!



I was busy helping to paint the living room and dining room last week so didn't get a chance to make anything so you can probably guess how much I'm itching to get my torch and some metal out and start playing again this week.
My next post will be about how I made a hollow form pendant with bezel set cab with the promised photos :D

Comments

  1. Gosh Tracy, this pendant is wonderful. You can't tell the '3Dness' of it from the first photo and then, as you read on, the pictures show more detail like a secret being revealed! Congratulations, it looks a masterpiece.
    Kristin :)

    ReplyDelete
  2. Thanks so much for your comments Kirsten and Vicky. I really enjoy making hollow form pieces and have lots of ideas floating around in my head at the mo :D And as always I'm still learning!

    ReplyDelete
  3. Love it! I have recently made something similar for myself. It's great fun to try something new and succeed!

    ReplyDelete
  4. Wow! I love these! The heart is so sweet. Your work is always amazing.

    ReplyDelete

Post a Comment

Your comments and questions are very welcome!
If you would prefer to contact me directly please use the contact form on my "get in touch" page.

Popular posts from this blog

Combining Soldering And Enamel

The need to make cute, brightly coloured enamel studs propelled me into the world of combining soldering with enamel a couple of years ago. I knew from reading up on it that it was possible to enamel and solder on the same piece but wasn't too confident I was able to do it back then. It was a slightly embarrassing occurance that made me just get on with - I'd made some enamel studs with glued on stud posts. I'd used 2 part epoxy resin which was a job in itself as it set hard after 5 minutes so I had to keep mixing more up. The finished studs looked ok but that little voice in my head kept asking "are you sure you want to use glue?" I wasn't but didn't think I had any other way to do it so I used glue. I sold my first pair and merrily sent them on their way to Canada. A couple of week later the buyer got in touch to say the stud post had come off one of the earrings and the other was hanging off. I was mortified, apologized profusely and refunded her m

Etching Silver Using Nail Art Stamps

So my love/hate relationship with etching sterling silver continues. I've tried a few times now and always end up with different results most of them not that great to be honest. I've tried connecting the silver and a piece of copper to a 9v battery and also heating the ferric nitrate. Sometimes the results are good sometimes not so good. I currently have an etched piece of silver sheet waiting to be reticulated and rid it of the mess that is the etched "pattern".  I now know that using stamps and Stayz On ink just doesn't work with silver - the time needed to etch using ferric nitrate is much longer than etching copper and the ink starts to wear away after about an hour. This results in the pattern being patchy as the resist is eaten away and the silver ends up quite lumpy and course looking. I have yet to try using pnp paper. I don't know why but it all seems a bit of a faff to do. I don't have a laser printer so would need to find somewhere or

Embossing Metal With My Sizzix Bigshot

I must admit up until a few weeks ago I was vaguely familiar with the name Sizzix but as to what you actually did with a "Sizzix" I was completely in the dark! That was until I stumbled across a video from Vintaj showing how you could use their embossing folders with a Bigshot to create designs on metal ("metal" - my favourite word after chocolate!) I was really impressed and itching to have a go, I just needed a Bigshot........ I waited a few weeks then when the urge to possess one overcame me I went out debit card at the ready..............and the shop had sold out! So I trundled off to The Range on the off chance and came home clutching my own surprisingly heavy pink and black wonder machine. It sat on the dining room table for a couple of days while I waited for the embossing folders I'd ordered online to arrive then the time came to start playing! I started with some pre-cut 24g copper hearts and the Wildflower Vines and the Butterfly Swirls Deco