Skip to main content

Colour Splash! Torch Enamel Earrings


I've been concentrating on bezel setting and soldering a lot recently so have been working mainly with metals of the silver and copper hue. So a bit like when your body tells you you need chocolate (all the time in my case) I got out the enamels recently to feed my craving for colour.
Enamels used to scare me when I first started using them and I was ultra careful about not contaminating them so as not to discover those little black specks and tiny pieces of wire wool that you never see until after you've fired something. I'm still careful but maybe a bit more relaxed these days. I recently had a problem with some transparent enamel I'd washed several months ago. I used it over opaque and it cracked. Not straight away because enamel likes to lull you into a false sense of security sometimes. No, one piece cracked a few hours after it was fired and the other a couple of days after. I reckoned it was because the washed enamel had been hanging around for a while and was probably contaminated.
I washed some more and it's worked fine this time as the earrings below show.


 I can't be the only one who finds the idea of washing a dry powder slightly odd. When I started torch enamelling and read that you needed to wash transparents if you want to use them over opaques I thought it seemed a bit of a chore and how can you "wash" a powder, how does it dry? 

It's really easy to do and involves putting a small amount of enamel into a shot glass or similar and filling it with water. You stir it, let it settle then pour off the water. This helps to remove a lot of the dust and other bits in the enamel powder you don't want. Do this until the water is clear(ish) using filtered water for the last rinse then blot as much of the excess water off the wet enamel powder with a kitchen roll as you can. Take care not to touch the enamel with the kitchen roll to avoid getting bits in the enamel. Then spread the wet enamel onto a clean piece of paper on top of a baking tray and put in the oven set to the lowest heat setting for about 10 -15 minutes to dry. When it's dry tip the enamel into a clean pot labelled so you know what it is. You do need to make sure everything you use is clean and doesn't have any bits or dust on it to avoid getting those bits in the washed enamel as they will show up when you fire it!
A bit of a fiddle but worth it. The alternative is muddy looking dirty colours.


I used three opaques for these - aqua, pea green and lichen green. My Mum used to say to me that blue and green should never be seen, usually as I was just off out on a Saturday night wearing blue and green! I never took any notice and reckon if these colours are good enough for nature they're good enough for me!


The colours in these orange and brown earrings remind me of an exotic colourful beetle. I used orange transparent over nut brown with a sprinkling of brown on top.

Next I'm planning on making some more small enamelled studs. I made some of these a while ago when I had just started soldering and found it terrible fraught and stressful! Enamel and solder aren't always easy to combine. I had to use enamel solder for the posts and was so worried things would melt or that the enamel would react with the solder. It didn't and everything was fine but I didn't enjoy the experience very much so haven't made any more, apart from a recent custom order. As I'm a bit more confident with the soldering part now I've decided to make some more even though they are fiddly to do. They are very cute when they're finished though :D




Comments

  1. I love your coloured earrings, especially the purple and green ones at the top - a great combination. Love the blue and green too!

    ReplyDelete
  2. I adore your enameled earrings! I've stayed away from the transparent enamels because I did not want to do the whole washing thing. But you've made it sound simpler than I thought it would be. And your results are lovely! I may order some of those now.

    ReplyDelete
  3. I like the concept of colour combination of earrings, its looks very pretty.

    ReplyDelete
  4. Love your use of colour. I have to confess I never wash my transparents I've had no trouble so far with cracking but then I always admire the quality of your enamelling so perhaps I should be more careful about my quality control.

    ReplyDelete
  5. Thanks for your comments, maybe I should make more enamel stuff!

    ReplyDelete
  6. Just such beautiful colours and shapes, a great selection of earrings. Thanks for sharing

    ReplyDelete
  7. Love how your colours are so bold! Do you also wash your opaque enamels?

    ReplyDelete
    Replies
    1. Thanks for your comment Laura! I don't wash opaque enamels normally. I'd only do it if the opaque enamel was contaminated with a lot of unwanted "bits" :D

      Delete

Post a Comment

Your comments and questions are very welcome!
If you would prefer to contact me directly please use the contact form on my "get in touch" page.

Popular posts from this blog

Combining Soldering And Enamel

The need to make cute, brightly coloured enamel studs propelled me into the world of combining soldering with enamel a couple of years ago. I knew from reading up on it that it was possible to enamel and solder on the same piece but wasn't too confident I was able to do it back then. It was a slightly embarrassing occurance that made me just get on with - I'd made some enamel studs with glued on stud posts. I'd used 2 part epoxy resin which was a job in itself as it set hard after 5 minutes so I had to keep mixing more up. The finished studs looked ok but that little voice in my head kept asking "are you sure you want to use glue?" I wasn't but didn't think I had any other way to do it so I used glue. I sold my first pair and merrily sent them on their way to Canada. A couple of week later the buyer got in touch to say the stud post had come off one of the earrings and the other was hanging off. I was mortified, apologized profusely and refunded her m

Etching Silver Using Nail Art Stamps

So my love/hate relationship with etching sterling silver continues. I've tried a few times now and always end up with different results most of them not that great to be honest. I've tried connecting the silver and a piece of copper to a 9v battery and also heating the ferric nitrate. Sometimes the results are good sometimes not so good. I currently have an etched piece of silver sheet waiting to be reticulated and rid it of the mess that is the etched "pattern".  I now know that using stamps and Stayz On ink just doesn't work with silver - the time needed to etch using ferric nitrate is much longer than etching copper and the ink starts to wear away after about an hour. This results in the pattern being patchy as the resist is eaten away and the silver ends up quite lumpy and course looking. I have yet to try using pnp paper. I don't know why but it all seems a bit of a faff to do. I don't have a laser printer so would need to find somewhere or

Embossing Metal With My Sizzix Bigshot

I must admit up until a few weeks ago I was vaguely familiar with the name Sizzix but as to what you actually did with a "Sizzix" I was completely in the dark! That was until I stumbled across a video from Vintaj showing how you could use their embossing folders with a Bigshot to create designs on metal ("metal" - my favourite word after chocolate!) I was really impressed and itching to have a go, I just needed a Bigshot........ I waited a few weeks then when the urge to possess one overcame me I went out debit card at the ready..............and the shop had sold out! So I trundled off to The Range on the off chance and came home clutching my own surprisingly heavy pink and black wonder machine. It sat on the dining room table for a couple of days while I waited for the embossing folders I'd ordered online to arrive then the time came to start playing! I started with some pre-cut 24g copper hearts and the Wildflower Vines and the Butterfly Swirls Deco