Skip to main content

More Bezel Setting Practice And Hollow Form Earrings


I wanted to do a bit more bezel setting to improve how long it takes me to do. I am getting quicker at it, really! I sometimes "waste" time cleaning/ filing/sanding bezels up then change my mind about what I'm going to do with them and realize I will have to sand them again after another lot of soldering. Oh well :D

I thought I'd try decorating one of the bezels by stamping. I wasn't sure if it would work as the bezel wire is pretty thin at 0.3mm so I stamped fairly lightly. I didn't want to risk stamping too heavily and the bezel splitting and I also left a gap where the join was going to be. I think it worked ok with these simple turquoise cabochon earrings.


I stamped in the gap I'd left after soldering but not directly over the solder join. I think the stamped effect looks "right" with the turquoise.

I'm currently practicing making hollow form pendants in copper and will move onto silver in the next couple of days. I love the 3D look of hollow form pieces - they look so solid but are lovely and light.
I made a pair of simple hollow form earrings in copper recently before I started on the pendants. Simple as in a domed disc soldered to a flat base which is then trimmed and finished.



The pendants I'm making consist of a frame plus a smaller frame in the centre which are soldered to a flat sheet on both sides. The middle of the smaller frame is pierced out after the first side is soldered and the edges are trimmed at the end. They are a bit tricky to solder to make sure the solder join is complete all the way round on both sides and around the smaller frame in the middle but I'm getting better and will post about them as soon as I've made a couple in silver.



I soon discovered when I made these earrings that it's important to make sure you rinse all of the pickle out of them. You need the hole to prevent the piece from exploding when you solder the earwire (or anything further) onto them but that also means they get full of any liquid you put them into! I find leaving them to soak in clean water and bicarb for 15 minutes after I take them out of the pickle does the trick.
I've also started using hard sterling wire for the earwires instead of dead soft and find it is a bit sturdier for this type of earwire despite being annealed when it's soldered and it worked out slightly cheaper than the dead soft which is always a good thing!!

Comments

  1. The earrings are beautiful!!

    ReplyDelete
  2. The turquoise earrings are definitely "right"--love 'em! And I really like reading about the process. Thanks for sharing.

    ReplyDelete
  3. It looks like you are progressing and your work is getting more & more lovely with each post!

    ReplyDelete
  4. Totally yummy! I absolutely love these!

    ReplyDelete
  5. This comment has been removed by a blog administrator.

    ReplyDelete
  6. I regularly visit your blog as I often get something out of it however this is the first time I have posted any comment (I'm more of a reader than a poster) but I just had to comment on the cabochon Turquoise earrings - they are so, so beautiful - the color of the turquoise is very pure looking - nice work!

    Jewellery Online

    ReplyDelete

Post a Comment

Your comments and questions are very welcome!
If you would prefer to contact me directly please use the contact form on my "get in touch" page.

Popular posts from this blog

Combining Soldering And Enamel

The need to make cute, brightly coloured enamel studs propelled me into the world of combining soldering with enamel a couple of years ago. I knew from reading up on it that it was possible to enamel and solder on the same piece but wasn't too confident I was able to do it back then. It was a slightly embarrassing occurance that made me just get on with - I'd made some enamel studs with glued on stud posts. I'd used 2 part epoxy resin which was a job in itself as it set hard after 5 minutes so I had to keep mixing more up. The finished studs looked ok but that little voice in my head kept asking "are you sure you want to use glue?" I wasn't but didn't think I had any other way to do it so I used glue. I sold my first pair and merrily sent them on their way to Canada. A couple of week later the buyer got in touch to say the stud post had come off one of the earrings and the other was hanging off. I was mortified, apologized profusely and refunded her m

Etching Silver Using Nail Art Stamps

So my love/hate relationship with etching sterling silver continues. I've tried a few times now and always end up with different results most of them not that great to be honest. I've tried connecting the silver and a piece of copper to a 9v battery and also heating the ferric nitrate. Sometimes the results are good sometimes not so good. I currently have an etched piece of silver sheet waiting to be reticulated and rid it of the mess that is the etched "pattern".  I now know that using stamps and Stayz On ink just doesn't work with silver - the time needed to etch using ferric nitrate is much longer than etching copper and the ink starts to wear away after about an hour. This results in the pattern being patchy as the resist is eaten away and the silver ends up quite lumpy and course looking. I have yet to try using pnp paper. I don't know why but it all seems a bit of a faff to do. I don't have a laser printer so would need to find somewhere or

Embossing Metal With My Sizzix Bigshot

I must admit up until a few weeks ago I was vaguely familiar with the name Sizzix but as to what you actually did with a "Sizzix" I was completely in the dark! That was until I stumbled across a video from Vintaj showing how you could use their embossing folders with a Bigshot to create designs on metal ("metal" - my favourite word after chocolate!) I was really impressed and itching to have a go, I just needed a Bigshot........ I waited a few weeks then when the urge to possess one overcame me I went out debit card at the ready..............and the shop had sold out! So I trundled off to The Range on the off chance and came home clutching my own surprisingly heavy pink and black wonder machine. It sat on the dining room table for a couple of days while I waited for the embossing folders I'd ordered online to arrive then the time came to start playing! I started with some pre-cut 24g copper hearts and the Wildflower Vines and the Butterfly Swirls Deco