Skip to main content

Using Titanium Soldering Clamps for Soldering Earring Posts


I wrote a post recently about forming soldering clamps from the Knew Concepts titanium strips I ordered sometime last year.
One of the most useful clamps I made was a shape that would help me to solder earring posts onto stud and open hoop earrings...


I can position it to hold the post like this for studs....


And like this for soldering posts onto open hoop style earrings....


Previously I was holding the piece of 20g post wire with a pair of tweezers in my right hand and the hoop was held in place using reverse action tweezers in a third hand as it is above. I would hold the torch in my left hand and as the flux heated up and became liquid I would find the post wire would start to move and I'd be forever stopping and trying to get it back in position. The metal for the hoops is only just over 1mm thick in some cases so that also used to make it a bit tricky and swearing would occur quite regularly!

Now that I can set it up with the titanium clamp holding the {much too long in this case!} post wire it's so much easier and less stressful. I flow some solder on to the end of the post wire and position it on the end of the hoop using the titanium clamp then after fluxing I hit the hoop with the torch for a few seconds and it's done.

The post wire is a really too long in the photo but I prefer to allow a bit extra so once the wire is soldered in position I can grab the end in my flat nose pliers and twist it to work harden the post. Then I trim it to size and file and sand the end so it's rounded and comfortable to put in.

Here's some more of the open hoop style earrings I made using the titanium clamp. The patterns are made using brass texture plates in the rolling mill.






Comments

  1. Such a great tool! I can only imagine the patience required to add posts to earrings. You do it beautifully! I am loving your hoops. :-)

    ReplyDelete
  2. Fascinating to see these in use - and successfully so! It looks so much easier soldering on earring posts this way than how I've done it before, which involved a lot of muttered swearing and the constant fear of everything melting!
    Thanks for sharing :)

    ReplyDelete
    Replies
    1. Completely agree about the muttered swearing and stress part :D

      Delete
  3. Nice! Seems like I need some the next visit to the shop I use. Thank You for the tip Tracy!

    ReplyDelete

Post a Comment

Your comments and questions are very welcome!
If you would prefer to contact me directly please use the contact form on my "get in touch" page.

Popular posts from this blog

Combining Soldering And Enamel

The need to make cute, brightly coloured enamel studs propelled me into the world of combining soldering with enamel a couple of years ago. I knew from reading up on it that it was possible to enamel and solder on the same piece but wasn't too confident I was able to do it back then. It was a slightly embarrassing occurance that made me just get on with - I'd made some enamel studs with glued on stud posts. I'd used 2 part epoxy resin which was a job in itself as it set hard after 5 minutes so I had to keep mixing more up. The finished studs looked ok but that little voice in my head kept asking "are you sure you want to use glue?" I wasn't but didn't think I had any other way to do it so I used glue. I sold my first pair and merrily sent them on their way to Canada. A couple of week later the buyer got in touch to say the stud post had come off one of the earrings and the other was hanging off. I was mortified, apologized profusely and refunded her m...

Torch Enamelling - What I've been Up To Recently!

I've admired enamelled jewellery for a while now and not too long ago did a blog post about Etsy seller tekaandzoe  and her wonderful kiln enamelled creations. I didn't think at the time that it was something I would ever be able to do as the cost of kilns plus lack of space would be a problem for me. That wasn't until I saw an advert for a torch enamelling tutorial from US jewellery supplies website Beaducation  by Steven James . It's a great tutorial showing the basics on how to torch enamel on copper. Of course I bought it! I then spent hours scouring the internet for more information on torch enamelling, where to buy the tools I'd need and of course the enamel powders. There are quite a few UK sites selling enamelling supplies and tools but as usual I found the US sites had more choice (why do we always lag behind?) I bought some enamel powders from a couple of UK sites to begin with - Cookson Gold have a good selection but bear in mind th...

Etching Silver Using Nail Art Stamps

So my love/hate relationship with etching sterling silver continues. I've tried a few times now and always end up with different results most of them not that great to be honest. I've tried connecting the silver and a piece of copper to a 9v battery and also heating the ferric nitrate. Sometimes the results are good sometimes not so good. I currently have an etched piece of silver sheet waiting to be reticulated and rid it of the mess that is the etched "pattern".  I now know that using stamps and Stayz On ink just doesn't work with silver - the time needed to etch using ferric nitrate is much longer than etching copper and the ink starts to wear away after about an hour. This results in the pattern being patchy as the resist is eaten away and the silver ends up quite lumpy and course looking. I have yet to try using pnp paper. I don't know why but it all seems a bit of a faff to do. I don't have a laser printer so would need to find somewhere or...