Skip to main content

A Splash Of Colour And Some Twirly Studs


I've been playing with my enamel colours again and creating my own "blends". It's fun sitting at the table with my different colours and mixing them up to make new ones. Enamels don't really mix to make new colours but you can achieve some really pretty speckly effects. Using the same colour groups work better than mixing colours opposite each other on the colour wheel. I found this out when I mixed some purple and lavender enamels with a bright green hoping I'd get a nice purple/green mix but it just looked grey when it was fired. If you looked closely you could see the individual colours but the overall effect was dull but luckily the beauty of enamelling is you can fix it with another layer (within reason!) What I have learned with mixing colours is if it looks dull in the pot it will still look dull when it's fired........... :D

The hoops above are enamelled in a mix of different greens with some transparent turquoise layered on top on the bottom section.


These were originally a really dull orangey-grey (one of my not so great mixes) so I revived them with some more opaque and transparent oranges and a sprinkling of cream and lighter orange on top. They make me think of marmalade.


This pair were victims of the purple/lavender/green horror mix so I brightened them up with more green opaques and a budgerigar green transparent. I love the effect sprinkling opaque enamel on top of transparent gives you, it reminds me of lichen.

I finished off a few simple stud earrings in copper and silver this week too. I used thin strips of metal and coiled them with round nose pliers like you would make a spiral to form cute twirls. I soldered the ends then after sanding one side flat I soldered them to a base, tidied them up then added posts and oxidized them.



The copper pair remind me of chelsea buns!
Labels:

Comments

  1. ClareioWednesday, October 30, 2013

    The silver studs look like roses, so pretty!!

    ReplyDelete
  2. Keith@ Vintage Crab Jewelry and CraftsWednesday, October 30, 2013

    Some beautiful work! I really like the studs as well as the colorful enamels!

    ReplyDelete
  3. Orion DesignsWednesday, October 30, 2013

    I love your enamel mixes. I've done some of that, but when I get too many layers, I also get cracks.

    Also, I've not yet worked with the transparent enamels. The thought of "washing" them has intimidated me. Do you wash your transparents? If so, is it as much of a pain as it sounds?

    ReplyDelete
  4. Cinnamon JewelleryWednesday, October 30, 2013

    Washing transparent enamels is pretty easy really it just sounds a bit strange!

    I just put a small amount into a shot glass and fill with water from the tap, stir it then leave for a couple of minutes to settle. Pour off the water and repeat until the water is "clear". I use filtered water for the last rinse but I don't think it matters that much if you are going to use it on top of opaques.
    To dry the powder, spread it onto a clean piece of paper on top of a baking sheet and put in the oven at the lowest setting for 10 - 15 minutes. Just make sure everything you use is clean and free of dust to avoid getting any more bits in the enamel powder.
    A bit of a faff but easy enough.

    ReplyDelete
  5. littlecherryhillWednesday, October 30, 2013

    Lovely lovely jewels! Great use of wire on those earrings too ♥

    ReplyDelete
  6. Miss Val's CreationsThursday, October 31, 2013

    I love the speckled look on the enameled piece. A neat effect! The swirl earrings are so cool.

    I'm not sure what a chelsea bun is but I would guess it is what we call a cinnamon bun since that is what they remind me of. :)

    ReplyDelete
  7. Cinnamon JewelleryThursday, October 31, 2013

    Thank you!
    Chelsea buns are similar to cinnamon buns but with added sultanas and candied peel. I made them at school years ago!

    ReplyDelete
  8. K S Jewellery DesignsSaturday, November 02, 2013

    Loving the twirly studs - such a clever design and executed to perfection! I too have recently been making studs and my jewellery tutor told me to set the posts off-centre towards the top but I'm not sure - what do you do?
    Kristin :)

    ReplyDelete
  9. Cinnamon JewellerySaturday, November 02, 2013

    Kirstin, your tutor probably said that as it's easier than getting the posts dead centre on a round pair. I try to get them centred and most times it works but the odd one does go a bit awry sometimes :D

    ReplyDelete
  10. NavMonday, November 04, 2013

    LOVELY WORK.
    Really great stuffs there :)

    Navneet
    www.navneetgems.blogspot.com

    ReplyDelete
  11. Elizabeth Prince CeramicsMonday, November 04, 2013

    love your colours - the turquoise is exquisite!

    ReplyDelete
  12. MartinSaturday, November 16, 2013

    You mentioned that the posts sometimes go awry and not 100% in the centre - sounds good to me. Perfection is overrated and something slightly off gives it character, in my very humble opinion!

    M

    ReplyDelete
  13. Cinnamon JewellerySaturday, November 16, 2013

    I agree Martin, perfection is over-rated!

    ReplyDelete

Post a Comment

Your comments and questions are very welcome!
If you would prefer to contact me directly please use the contact form on my "get in touch" page.

Popular posts from this blog

Combining Soldering And Enamel

The need to make cute, brightly coloured enamel studs propelled me into the world of combining soldering with enamel a couple of years ago. I knew from reading up on it that it was possible to enamel and solder on the same piece but wasn't too confident I was able to do it back then. It was a slightly embarrassing occurance that made me just get on with - I'd made some enamel studs with glued on stud posts. I'd used 2 part epoxy resin which was a job in itself as it set hard after 5 minutes so I had to keep mixing more up. The finished studs looked ok but that little voice in my head kept asking "are you sure you want to use glue?" I wasn't but didn't think I had any other way to do it so I used glue. I sold my first pair and merrily sent them on their way to Canada. A couple of week later the buyer got in touch to say the stud post had come off one of the earrings and the other was hanging off. I was mortified, apologized profusely and refunded her m...
32 comments
Read more

Torch Enamelling - What I've been Up To Recently!

I've admired enamelled jewellery for a while now and not too long ago did a blog post about Etsy seller tekaandzoe  and her wonderful kiln enamelled creations. I didn't think at the time that it was something I would ever be able to do as the cost of kilns plus lack of space would be a problem for me. That wasn't until I saw an advert for a torch enamelling tutorial from US jewellery supplies website Beaducation  by Steven James . It's a great tutorial showing the basics on how to torch enamel on copper. Of course I bought it! I then spent hours scouring the internet for more information on torch enamelling, where to buy the tools I'd need and of course the enamel powders. There are quite a few UK sites selling enamelling supplies and tools but as usual I found the US sites had more choice (why do we always lag behind?) I bought some enamel powders from a couple of UK sites to begin with - Cookson Gold have a good selection but bear in mind th...
37 comments
Read more

Etching Silver Using Nail Art Stamps

So my love/hate relationship with etching sterling silver continues. I've tried a few times now and always end up with different results most of them not that great to be honest. I've tried connecting the silver and a piece of copper to a 9v battery and also heating the ferric nitrate. Sometimes the results are good sometimes not so good. I currently have an etched piece of silver sheet waiting to be reticulated and rid it of the mess that is the etched "pattern".  I now know that using stamps and Stayz On ink just doesn't work with silver - the time needed to etch using ferric nitrate is much longer than etching copper and the ink starts to wear away after about an hour. This results in the pattern being patchy as the resist is eaten away and the silver ends up quite lumpy and course looking. I have yet to try using pnp paper. I don't know why but it all seems a bit of a faff to do. I don't have a laser printer so would need to find somewhere or...
34 comments
Read more