Skip to main content

Using Enamel Cabochons In My Jewellery



I know how to torch enamel and I know how to bezel set cabochons so I thought it was about time I put the two together! I've been thinking about it for "ages" and last week I actually got round to doing it. I started small (of course I did, I like to make life difficult!) and made four 9mm cabs from copper.

The enamelling was a bit tricky and Klyre Fire was called for so the enamel powder stuck to the front of the cab and didn't slide off. I discovered it was better to gently (very gently!) dry the klyre fire using my torch than let it air dry as it is very easy to knock the cab once the klyre fire is dry and watch the enamel slide right off. I got there in the end and produced two dusky pink and two sea green enamel cabs.


I was then slightly paranoid that they would crack but as they are formed (domed) and counter enamelled for added stability they were fine. I had to be a bit more careful than normal when it came to handling them and when I set them as they are a bit more delicate than stone cabs. I used my wooden bezel pusher - a customised peg in other words - to set them and it worked out fine. I made a copper and silver heart pendant using the zentangle etched copper I made recently and a pair of sterling silver disc earrings with the green enamel cabs.



I've yet to decide what to do with the second pink cab but at the mo I'm thinking a silver pendant.........maybe!
I enjoyed making both of these pieces and can feel myself slowly getting more confident with my soldering. I love that making my own enamelled cabs means I can make virtually whatever colour I want. Next time I'll make life easier and go bigger and will probably take photos too :D
Labels:

Comments

  1. UnknownFriday, August 02, 2013

    That locket was superb really.

    ReplyDelete
  2. DeborahRead.comFriday, August 02, 2013

    Beautiful work

    ReplyDelete
  3. Cinnamon JewelleryFriday, August 02, 2013

    Thank you!!

    ReplyDelete
  4. littlecherryhillTuesday, August 06, 2013

    Lovely work Tracy! Spesh love those silver earrings, you wouldn't ever guess they were enamelled cabs, well done!

    ReplyDelete
  5. Vickie DevenportFriday, March 03, 2017

    I can't help but feel we must be on the same wave length.....ever since I've discovered your wonderful blog, I have been amazed with the work you are doing! It is like I have found a kindred spirit in the process of learning new jewelry techniques, and I love how you describe your new experiences! I have been thinking about trying a torch fired enamel cab, and voile! You have given me inspiration! Thank you so very much for the work you share, and the beautiful artist that you are!

    ReplyDelete
    Replies
    1. Cinnamon JewelleryFriday, March 03, 2017

      Thanks for your lovely comment Vickie, it's good to know my posts are useful. I've just got a kiln and am in the process of getting used to enamelling with it....it's a bit of a learning curve :D

      Delete

Post a Comment

Your comments and questions are very welcome!
If you would prefer to contact me directly please use the contact form on my "get in touch" page.

Popular posts from this blog

Combining Soldering And Enamel

The need to make cute, brightly coloured enamel studs propelled me into the world of combining soldering with enamel a couple of years ago. I knew from reading up on it that it was possible to enamel and solder on the same piece but wasn't too confident I was able to do it back then. It was a slightly embarrassing occurance that made me just get on with - I'd made some enamel studs with glued on stud posts. I'd used 2 part epoxy resin which was a job in itself as it set hard after 5 minutes so I had to keep mixing more up. The finished studs looked ok but that little voice in my head kept asking "are you sure you want to use glue?" I wasn't but didn't think I had any other way to do it so I used glue. I sold my first pair and merrily sent them on their way to Canada. A couple of week later the buyer got in touch to say the stud post had come off one of the earrings and the other was hanging off. I was mortified, apologized profusely and refunded her m...
32 comments
Read more

Torch Enamelling - What I've been Up To Recently!

I've admired enamelled jewellery for a while now and not too long ago did a blog post about Etsy seller tekaandzoe  and her wonderful kiln enamelled creations. I didn't think at the time that it was something I would ever be able to do as the cost of kilns plus lack of space would be a problem for me. That wasn't until I saw an advert for a torch enamelling tutorial from US jewellery supplies website Beaducation  by Steven James . It's a great tutorial showing the basics on how to torch enamel on copper. Of course I bought it! I then spent hours scouring the internet for more information on torch enamelling, where to buy the tools I'd need and of course the enamel powders. There are quite a few UK sites selling enamelling supplies and tools but as usual I found the US sites had more choice (why do we always lag behind?) I bought some enamel powders from a couple of UK sites to begin with - Cookson Gold have a good selection but bear in mind th...
37 comments
Read more

Etching Silver Using Nail Art Stamps

So my love/hate relationship with etching sterling silver continues. I've tried a few times now and always end up with different results most of them not that great to be honest. I've tried connecting the silver and a piece of copper to a 9v battery and also heating the ferric nitrate. Sometimes the results are good sometimes not so good. I currently have an etched piece of silver sheet waiting to be reticulated and rid it of the mess that is the etched "pattern".  I now know that using stamps and Stayz On ink just doesn't work with silver - the time needed to etch using ferric nitrate is much longer than etching copper and the ink starts to wear away after about an hour. This results in the pattern being patchy as the resist is eaten away and the silver ends up quite lumpy and course looking. I have yet to try using pnp paper. I don't know why but it all seems a bit of a faff to do. I don't have a laser printer so would need to find somewhere or...
34 comments
Read more