Skip to main content

Summer Colour - Enamel Flower Earrings and Pendants


After a few weeks of concentrating on metalwork making hollow form pendants and earrings I needed a burst of colour so out came the enamel powders and some pretty pre-cut copper flower blanks. Yes I could saw out the flowers myself but I didn't :D
I felt like mixing up the colours a bit by sifting a mixture of opaque enamels together and firing at the same time. Previously I would only do one colour and fire it then add another colour, fire, then another colour but mixing the second layer of enamel colours saves time and doesn't do any harm. Mixing two different enamel powders won't result in a new colour as such, eg. mixing red and yellow won't produce orange but a speckled blend of red and yellow. Mixing similar shades is good as the different coloured speckles aren't as obvious so the end colour looks more solid. It gives you more options.

The earrings above are a base layer of seafoam then another layer of seafoam mixed with lichen and pea which produced a lovely sea green shade with sprinkles of brown and cream added on top.


I made a pendant with the same colours but this time I mixed the seafoam, lichen amd pea enamels and put them in a pot. The resulting colour was slightly different to the earrings but that's the fun of mixing your own blends - you don't know how they will turn out until you fire them the first time. You can then add another colour in the second layer to change the overall look if you want to. As I'm writing this I've had a sudden urge to try to achieve an ombre effect with similar shades of enamel. I think applying the enamels wet with a brush will be the way to go. This idea obviously need some thought.........


These bright young things, currently on their way to Oregon, are a mixture of sunset orange with sprinklings of scarlet, pink and brown. The pink completely disappeared in the orange and the brown is very subtle too (in other words you can hardly see it!)


I was asked to make the pendant for a custom order which means I'm now out of the cute flower blanks. I did create a few templates just in case I had a sudden rush of blood to the head and felt like sawing out my own flowers which I may do as I now do enjoy sawing which is something I never thought I would say, or I might just buy a few more which would be much easier if a bit more expensive!


I wanted to use up some sterling beads and spacers I've had for ever so combined them with some more mixed colour enamel discs and "lily pads". It's nice to do a bit of wirework every now and then!

Comments

  1. I always love seeing what you are up to! The flowers are so pretty and sweet. Love those lily pads too!

    ReplyDelete
  2. Your enamels are delicious, Tracy... have you considered selling enameled components?

    ReplyDelete
  3. Thank Monique. Funnily enough I did think about doing that very thing and selling enamelled discs and links :D

    ReplyDelete
  4. Very pretty! I love the colours on the first earrings especially.

    ReplyDelete
  5. I love your collection flower earrings are very beautiful combination of orange with red is awesome.

    ReplyDelete

Post a Comment

Your comments and questions are very welcome!
If you would prefer to contact me directly please use the contact form on my "get in touch" page.

Popular posts from this blog

Combining Soldering And Enamel

The need to make cute, brightly coloured enamel studs propelled me into the world of combining soldering with enamel a couple of years ago. I knew from reading up on it that it was possible to enamel and solder on the same piece but wasn't too confident I was able to do it back then. It was a slightly embarrassing occurance that made me just get on with - I'd made some enamel studs with glued on stud posts. I'd used 2 part epoxy resin which was a job in itself as it set hard after 5 minutes so I had to keep mixing more up. The finished studs looked ok but that little voice in my head kept asking "are you sure you want to use glue?" I wasn't but didn't think I had any other way to do it so I used glue. I sold my first pair and merrily sent them on their way to Canada. A couple of week later the buyer got in touch to say the stud post had come off one of the earrings and the other was hanging off. I was mortified, apologized profusely and refunded her m...

Torch Enamelling - What I've been Up To Recently!

I've admired enamelled jewellery for a while now and not too long ago did a blog post about Etsy seller tekaandzoe  and her wonderful kiln enamelled creations. I didn't think at the time that it was something I would ever be able to do as the cost of kilns plus lack of space would be a problem for me. That wasn't until I saw an advert for a torch enamelling tutorial from US jewellery supplies website Beaducation  by Steven James . It's a great tutorial showing the basics on how to torch enamel on copper. Of course I bought it! I then spent hours scouring the internet for more information on torch enamelling, where to buy the tools I'd need and of course the enamel powders. There are quite a few UK sites selling enamelling supplies and tools but as usual I found the US sites had more choice (why do we always lag behind?) I bought some enamel powders from a couple of UK sites to begin with - Cookson Gold have a good selection but bear in mind th...

Etching Silver Using Nail Art Stamps

So my love/hate relationship with etching sterling silver continues. I've tried a few times now and always end up with different results most of them not that great to be honest. I've tried connecting the silver and a piece of copper to a 9v battery and also heating the ferric nitrate. Sometimes the results are good sometimes not so good. I currently have an etched piece of silver sheet waiting to be reticulated and rid it of the mess that is the etched "pattern".  I now know that using stamps and Stayz On ink just doesn't work with silver - the time needed to etch using ferric nitrate is much longer than etching copper and the ink starts to wear away after about an hour. This results in the pattern being patchy as the resist is eaten away and the silver ends up quite lumpy and course looking. I have yet to try using pnp paper. I don't know why but it all seems a bit of a faff to do. I don't have a laser printer so would need to find somewhere or...