Skip to main content

Handmade Copper Bangles




Not usually something that crosses my radar being a committed earring freak, strangely I had a sudden urge a couple of weeks ago to make some bangles. I made the first one at night school as I needed something to do in the last couple of weeks that wouldn't take too long. I enjoyed making it - it was a hammered round bangle made from 2.6mm copper wire which I soldered three coils of thinner wire to.



 I soon discovered that soldering the coils onto it meant I couldn't reshape it. I used paste solder for the coils as I thought it would be easier but two attempts and some burnt blobby messes later I went back to sheet solder which worked. In the meantime the bracelet had been bent out of shape slightly plus it needed a good hammering to work harden it as it was a little "bendy" having been well annealed with my soldering attempts!
So having learned what not to do - I never got on with paste solder so why I used it I don't know! - I bought a bracelet mandrel and made a few more -







They are made from 2.6mm and 3.25mm copper wire and are textured with a hammer and stamped designs. Really fun and easy to make.






The twisted wire bangles were a bit more work. I rolled the wire through the rolling mill at college then twisted the flattened wire using a vice and big pair of pliers. Matching the join and soldering was a challenge - I discovered that wedging the solder in the join was the best bet as it had a habit of sliding round the twist as I started to heat up the wire. Thinking about it now pick soldering the join probably would've been a better option and even easier!


Labels:

Comments

  1. AliciaMonday, June 10, 2013

    AHH those bangles are beautiful, I'm still trying to master bangles and I'm not doing very well so far

    ReplyDelete
  2. Cinnamon JewelleryMonday, June 10, 2013

    Thanks Alicia

    ReplyDelete
  3. AnonymousFriday, June 28, 2013

    You have very good construction technique and you attention to finishing is a breath of fresh air in what passes for metalsmithing these days!

    ReplyDelete

Post a Comment

Your comments and questions are very welcome!
If you would prefer to contact me directly please use the contact form on my "get in touch" page.

Popular posts from this blog

Combining Soldering And Enamel

The need to make cute, brightly coloured enamel studs propelled me into the world of combining soldering with enamel a couple of years ago. I knew from reading up on it that it was possible to enamel and solder on the same piece but wasn't too confident I was able to do it back then. It was a slightly embarrassing occurance that made me just get on with - I'd made some enamel studs with glued on stud posts. I'd used 2 part epoxy resin which was a job in itself as it set hard after 5 minutes so I had to keep mixing more up. The finished studs looked ok but that little voice in my head kept asking "are you sure you want to use glue?" I wasn't but didn't think I had any other way to do it so I used glue. I sold my first pair and merrily sent them on their way to Canada. A couple of week later the buyer got in touch to say the stud post had come off one of the earrings and the other was hanging off. I was mortified, apologized profusely and refunded her m...
32 comments
Read more

Torch Enamelling - What I've been Up To Recently!

I've admired enamelled jewellery for a while now and not too long ago did a blog post about Etsy seller tekaandzoe  and her wonderful kiln enamelled creations. I didn't think at the time that it was something I would ever be able to do as the cost of kilns plus lack of space would be a problem for me. That wasn't until I saw an advert for a torch enamelling tutorial from US jewellery supplies website Beaducation  by Steven James . It's a great tutorial showing the basics on how to torch enamel on copper. Of course I bought it! I then spent hours scouring the internet for more information on torch enamelling, where to buy the tools I'd need and of course the enamel powders. There are quite a few UK sites selling enamelling supplies and tools but as usual I found the US sites had more choice (why do we always lag behind?) I bought some enamel powders from a couple of UK sites to begin with - Cookson Gold have a good selection but bear in mind th...
37 comments
Read more

Etching Silver Using Nail Art Stamps

So my love/hate relationship with etching sterling silver continues. I've tried a few times now and always end up with different results most of them not that great to be honest. I've tried connecting the silver and a piece of copper to a 9v battery and also heating the ferric nitrate. Sometimes the results are good sometimes not so good. I currently have an etched piece of silver sheet waiting to be reticulated and rid it of the mess that is the etched "pattern".  I now know that using stamps and Stayz On ink just doesn't work with silver - the time needed to etch using ferric nitrate is much longer than etching copper and the ink starts to wear away after about an hour. This results in the pattern being patchy as the resist is eaten away and the silver ends up quite lumpy and course looking. I have yet to try using pnp paper. I don't know why but it all seems a bit of a faff to do. I don't have a laser printer so would need to find somewhere or...
34 comments
Read more